| |
|
HDMI to DVI-D Super High Resolution™ Copper Cables
|
|
|
Superior Performance — DVIGear’s Super High Resolution™ (SHR™) HDMI to DVI cables are engineered for unsurpassed performance and reliability in mission critical applications. These cables are designed to transport high speed digital DVI and HDMI signals over very long distances while maintaining pristine signal / bit integrity.
High-Speed Signals — Long distance transport of high resolution DVI and HDMI signals over copper cables must overcome several challenges, such as insertion loss, differential skew and jitter. Insertion loss is caused by cable capacitance, which acts as a low-pass filter, blocking higher frequency signal components from passing. Skew occurs when the differential DVI and HDMI signals get delayed and become out of phase as they pass over a long cable. Both factors contribute to increased digital jitter, which degrades the performance of the cable. This jitter becomes more severe with higher resolutions and longer cable distances. Conventional cables that support lower resolutions at short distances are often unable to support the data rates required by higher resolutions at longer distances. The resulting video can be disrupted by visual artifacts or may not be visible at all.
Advanced Design — Built to overcome these challenges, the SHR™ Series HDMI to DVI Cables are constructed using heavy gauge 22AWG copper wires. This increases the cross-sectional cable area and decreases the capacitance of the cables, which allows signals with higher data rates to pass with minimal jitter. When coupled with DVIGear’s Active Cable Extenders (ACE™), cable lengths of up to 200 ft. (~ 60 meters) are possible while maintaining full compliance with DVI and HDMI signal parameters. The combination of these products are active copper cables with minimal insertion loss and skew. These cables rival the performance of fiber cables at a fraction of the cost, while providing superior ruggedness and durability.
Key Features:
- Cables 20m or longer include DVIGear's ACE™ (Active Cable Extender)
- Supports HDTV resolutions up to 1080p with 12-bit color
- Supports PC resolutions up to 1920x1200 and 2048x1080 at cable lengths up to 60m
- Supports HDMI data rates up to 3.4 Gpbs. at lengths up to 7.5m
- Supports HDMI data rates up to 2.25 Gbps. at lengths up to 40m
|
|
- Supports PC data rates up to 1.65 Gbps. at lengths up to 60m
- Heavy-duty 22AWG copper wires provide minimal insertion loss
- Ultra-low Skew guarantees unsurpassed digital fidelity
- Triple shielded for superior noise immunity
- Dual UL Ratings: UL13 (CL2) and UL758 (AWM20276). These cables are in-wall rated.
|
Note 1: Includes Active Cable Extender™ and 0.5 meter cable. Depending on specific application requirements, either an HDMI or Single-Link DVI ACE™ unit may be selected.
Note2: This product is End of Life and is no longer available.
|
Product Designation
|
SHR™
|
|
Product Description
|
22AWG HDMI to DVI-D Cables
|
|
Input / Output Connectors
|
1x 19-pin HDMI Male Connector, 1x 18+1 DVI Male Connector
|
|
Contacts
|
19 pins, 30μ Gold Plated, long life design
|
|
Shell
|
Gold Flash Plated
|
|
Standards Compliance
|
DVI 1.0, HDMI 1.3
|
|
Maximum Pixel Clock Frequency
|
165 MHz - up to 60 meters
225 MHz - up to 40 meters
340 MHz - up to 7.5 meters
|
|
Maximum Bit Rate (per Channel)
|
1.65 Gbps - up to 60 meters
2.25 Gbps - up to 40 meters
3.40 Gbps - up to 7.5 meters
|
|
Maximum Bit Rate (Aggregate)
|
4.95 Gbps - up to 60 meters
6.75 Gbps - up to 40 meters
10.2 Gbps - up to 7.5 meters
|
|
Supported HDTV Resolutions
|
1080p / 60 Hz with 8, 10 and 12-bit color
|
|
Supported Single-Link PC Resolutions
|
Up to 2048x1080, 1920x1200
|
|
Supported Dual-Link PC Resolutions
|
n/a
|
|
Cable Equalization
|
DVIGear's Active Cable Extender (ACE™) is included with cables 20 meters (~ 65.6 ft.) and longer.
|
|
Voltage Rating
|
75 V
|
|
Differential Impedance
|
100 ohms ± 5%
|
|
Insertion Loss (SDD21)
|
< 32 dB @ 825 MHz with 60 meter cable
|
|
Intra-pair Skew
|
< 2.2 nsec (from 250 MHz - 2.5 GHz) with 60 meter cable
|
|
Inter-pair Skew
|
< 150 psec (from 250 MHz - 2.5 GHz) with 60 meter cable
|
|
Far End Crosstalk (FEXT)
|
< -20 dB
|
|
Propagation Delay
|
4.55 nsec/meter
|
|
Available Cable Lengths (meters) (1)
|
0.5, 1, 2, 3, 5, 7.5, 10, 12.5, 15, 20, 25, 30, 35, 40, 45, 50, 60
|
|
Available Cable Lengths (ft.) (1)
|
1.6, 3.3, 6.6, 9.8, 16.4, 24.6, 32.8, 41.0, 49.2, 65.6, 82.0, 98.4, 114.8,
131.2, 147.6, 164.0, 196.9
|
|
Maximum Cable Length
|
200 ft. (~ 60 meters)
|
|
Construction
|
19 Conductor Cable with 4x high speed twisted pairs
|
|
High Speed Conductors
|
22AWG, FM-PE+SKIN Construction
|
|
Shielding
|
Triple Shielding
|
|
Jacket Material / Color
|
PVC / Blue (PMS 301c)
|
|
Outside Diameter
|
11.50 ± 0.20 mm
|
|
Minimum Bend Radius
|
43.5 mm
|
|
Operating Temperature
|
-13° to 140° F (-25° to 60° C)
|
|
Storage Temperature
|
-40° to 167° F (-40° to 75° C)
|
|
Humidity (storage / operating)
|
10% to 90% (non-condensing)
|
|
Compliance
|
UL13 (CL2)
UL758 (AWM20276)
RoHS
|
|
UL File Numbers
|
AVLV2.E245407
AVLV8.E245407
QPTZ.E245576
|
|
Limited Warranty
|
3 Years
|
|
DVIGear's Active Cable Extender (ACE™) is included with cables 20 meters (~ 65.6 ft.) and longer.
|
Note 1: Active Cable Extender™ included with all cables 20 meters (~ 65.6 ft.) and longer. Depending on application requirements, either HDMI or DVI Single-Link ACE™ unit may be selected.
|
 |
DVI-7171c
Extends Single-Link DVI Cables up to 200 ft. (~ 60 meters).
HDMI or DVI ACE™ unit included with all cables 20 meters (~ 65 ft.) and longer.
|
|
|
|
|
 |
DVI-7370c
Extends HDMI Cables up to 200 ft. (~ 60 meters).
HDMI or DVI ACE™ unit included with all cables 20 meters (~ 65 ft.) and longer.
|
|
|
|
|
 |
DVI-8511c
DVI-8511c is a 10-inch Adapter Cable that allows the connection of a DVI cable to an HDMI device. It is constructed using lightweight 28 AWG wire, which makes it very flexible.
|
|
|
|
1.888.463.9927 
+1.770.421.6699
